伟德BV下载-平台【首页】

电阻式微型电流保险丝

电阻式微型电流保险丝

服务项目:电阻式微型电流保险丝

点击次数:20059  次

详细信息:

伟德BV下载代理销售各式型号电阻式微型电流保险管,其体积小,外形像插件电阻式样,可以按照空间特性弯角整形成各式形状插脚进PCB上面,操作方便,安全可靠。

其具体规格如下:

一、

2T 3*8电阻式微型/环氧树脂/慢断微型电流保险丝


产品详情

1.规格型号和安规认证

MODEL  NUMBER  AND  SAFETY  CERTIFICATION

1-1 品名规格:系列号+额定电流+额定电压+认证符号

Model  Number:  Part  Number+Rated Current+Rated Voltage+Approvals.

例子[example]:

2T        1.2     250V                  1)系列号Part  Number

2) 额定电流  Rated  Current

1)         2)       3)                  3) 额定电压  Rated  Voltage

1-2额定电流和额定电压

Rated Current  And  Voltage

额定电流: 32mA~1

Rated Current: 32 mA~1

额定电压;125V/250V/400V AC

Rated  Voltage:125V/250V/400 AC

1-3标示Marking

保险管上需有下列标示

The fuse shall have the following marking:

规格:特性符号+额定电流+额定电压

Specification:Characteristic  Symbol+Rated Voltage

32mA~800mA : _mA    1A~1:_A

Trade mark:The Manufacture’s Logo+Part Number+Approvals

32mA~1:UL CSA

注意:对标示字样大小没有规定

Note:Size of the markings have not be specified.

2.适用范围

SCOPE

适用于一般电子设备。Used in electronic equipment.

3.工程图和结构

OUTLINE DRAWING AND STRUCTURE

3-1 工程图(?挝唬?m)

Outline Drawing and Dimensions(Unit:mm)

3-2结构

Structure

编号

No.

元件

Component

材?

Material

?盗?/span>

Quantity

(1)

熔?

Wire

合金

Alloy

1

(2)

?帽

Cap

????

Brass with mickel plated

2

(3)

本?

Body

陶瓷管/胶料

Ceramic Tube/Plastic

1

(4)

引?

Lead

????

Tinned Copper wire

2

(5)

镀层

Insulating Coat

环氧树脂

Epoxy Resin

/

4.外?及形?

APPEARANCES AND CONFIGURATION

4-1外?:外观不应有显著的污点、铁锈或者裂纹

Appearances:There shall not be any remaekable stain,rust or crack on the appearances.

4-2形?睿褐嵯蛞?诺某?⌒捅O账

Configuration:Axial Leaded Micro-Fuse.

5.物理特性

PHYSICAL CHARACTERISTIC

5-1 拉力?y?

Tensile test

沿端子的?向施加10N的拉力,持?1分?。

Keep pulling the cap of the fuse with 10N at axial direction for 1 min.

6.??馓匦

ELECTRICAL CHARACTERISTICS

% of Ampere Rating

Ampere Rating

Opening Time

100%

32mA - 1

4 Hours, Min.

200%

32mA - 1

60 Second, Max

275%

500mA~ 10A

300 msecs., Max.

400%

500mA~ 10A

30 msecs., Max.

1000%

500mA~ 10A

4 msecs., Max.

规格判定Item

Openrating Temp

-55℃~125

大熔断时限

200% Rating 60SEC

突波实验

3millisecond at 1000% rated current

Melting I 2 t

1.83~2.083

Cold Ohms

1.2/0.058~0.067 Ohm

Interrupting rating

50A/125VAC

50A/250VAC

Dimensions

9mm*¢3.9mm

Ssfty

UL CSA CCC ROHS

7.?境特性

ENVIRONMENTAL SPECIFICATION

7-1 操作?囟裙????55℃~125℃

Operating Temperature: -55℃~125℃

7-2 保存?l件

Storage Conditions

?囟龋?10℃~60℃

Temperature: +10℃~60℃

在相??穸取?5%下平均可存放3年

On average, It can be stored below the relative humidity or 75% for 3 years.

在非露天下,相??穸??5%下多可存放30天。

Without dew, It can be kept under humidity of 95% for 30 days.

8.焊接?l件

SOLDERING PAAMETERS

8-1波峰焊

Wave Solder

焊接?囟龋?60±5℃

Soldering Temperature:260±5℃

焊接?r?:4 Sec. Max.

Soldering Time:4 Sec.Max.

8-2手工焊?

Manual Solder

焊接?囟龋?50±5℃

Soldering Temperature: 350±5℃

焊接?r?:3 Sec. Max.

Soldering Time: 3 Sec. Max.

9.其他使用注意事?

OTHER NOTICE IN USING

如果需在保??上加?峥s套管,烘烤?囟扰c?r?需?⒄找韵乱?定

If heat shrink tubing was needed,the roast temperature and time should be refer to the following.

?定烘烤?囟龋翰淮箪?50℃  烘烤?r?:50s Max.

The temperature should be sel under 150℃,roast time:50s Max.

二、2F-3x8 电阻式 快断 陶瓷保险管



产品详情

1.规格型号和安规认证

MODEL  NUMBER  AND  SAFETY  CERTIFICATION

1-1 品名规格:系列号+额定电流+额定电压+认证符号

Model  Number:  Part  Number+Rated Current+Rated Voltage+Approvals.

例子[example]:

2T           2A     400V                  1)系列号  Part  Number

2)额定电流  Rated  Current

1)          2)      3)                 3)额定电压  Rated  Voltage

1-2额定电流和额定电压

Rated Current  And  Voltage

额定电流: 100mA~10A

Rated Current: 32 mA~1

额定电压;125V/250V/400V AC

Rated  Voltage:125V/250V/400 AC

1-3标示Marking

保险管上需有下列标示

The fuse shall have the following marking:

规格:特性符号+额定电流+额定电压

Specification:Characteristic  Symbol+Rated Voltage

100mA~800mA : _mA    1A~10A:_A

Trade mark:The Manufacture’s Logo+Part Number+Approvals

100mA~10A: TUV UL CSA CQC

注意:对标示字样大小没有规定

Note:Size of the markings have not be specified.

2.适用范围

SCOPE

适用于一般电子设备。Used in electronic equipment.

3.工程图和结构

OUTLINE DRAWING AND STRUCTURE

3-1 工程图(?挝唬?m)

Outline Drawing and Dimensions(Unit:mm)

3-2结构Structure

编号

No.

元件

Component

材质

Material

数量

Quantity

(1)

熔丝

Wire

合金

Alloy

1

(2)

铜帽

Cap

黄铜镀镍

Brass with mickel plated

2

(3)

本体

Body

陶瓷管

Ceramic Tube

1

(4)

引线

Lead

镀锡铜线

Tinned Copper wire

2


4.外观及形状

APPEARANCES AND CONFIGURATION

4-1外观:外观不应有显著的污点、铁锈或者裂纹

Appearances:There shall not be any remaekable stain,rust or crack on the appearances.

4-2形?睿褐嵯蛞?诺某?⌒捅O账

Configuration:Axial Leaded Micro-Fuse.

5.物理特性

PHYSICAL CHARACTERISTIC

5-1 拉力?y?

Tensile test

沿端子的轴向施加10N的拉力,持续1分?,管体不断开、破裂。

Keep pulling the cap of the fuse with 10N at axial direction for 1 min,and the pipe body is continuously opened and broken.

5-2管体强度测试

Strength of fuse tube

保险管管体固定好后,在管体中央部位施加15N压力,管体不断开、破裂。

After the fuse pipe body is fixed, the 15N pressure is applied to the center position of the pipe body, and the pipe body is continuously opened and broken.

6.电气特性

ELECTRICAL CHARACTERISTICS

% of Ampere Rating

Ampere Rating

Opening Time

100%

100mA - 10A

4 Hours, Min.

200%

100mA - 10A

60 Second, Max

275%

500mA~ 10A

300 msecs., Max.

400%

500mA~ 10A

30 msecs., Max.

1000%

500mA~ 10A

4 msecs., Max.

7.环境特性

ENVIRONMENTAL SPECIFICATION

7-1 操作温度范围:-55℃~125℃

Operating Temperature: -55℃~125℃

7-2 保存条件

Storage Conditions

温度:+10℃~60℃

Temperature: +10℃~60℃


在相对湿度≤75%下平均可存放3年

On average, It can be stored below the relative humidity or 75% for 3 years.

在非露天下,相对湿度为95%下多可存放30天。

Without dew, It can be kept under humidity of 95% for 30 days.

8.焊接条件

SOLDERING PAAMETERS

8-1波峰焊

Wave Solder

焊接?囟龋?60±5℃

Soldering Temperature:260±5℃

焊接时间:4 Sec. Max.

Soldering Time:4 Sec.Max.

8-2手工焊锡

Manual Solder

焊接温度:350±5℃

Soldering Temperature: 350±5℃

焊接时间:3 Sec. Max.

Soldering Time: 3 Sec. Max.

9.其他使用注意事项

OTHER NOTICE IN USING

如果需在保险管上加热缩套管,烘烤温度与时间需参照以下规定

If heat shrink tubing was needed,the roast temperature and time should be refer to the following.

设定烘烤温度:不大于150℃  烘烤?r?:50s Max.

The temperature should be sel under 150℃,roast time:50s Max.

三、2.4X7电阻式 慢断 微型环氧树脂保险丝 TUV UL CSA CQC


产品详情

1.规格型号和安规认证

MODEL  NUMBER  AND  SAFETY  CERTIFICATION

1-1 品名规格:系列号+额定电流+额定电压+认证符号

Model  Number:  Part  Number+Rated Current+Rated Voltage+Approvals.

例子[example]:

2SMT/2T      2A     400V                         1)系列号 Part  Number

2)额定电流  Rated  Current

1)          2)      3)                            3)额定电压  Rated  Voltage

1-2额定电流 和额定电压

Rated Current  And  Voltage

额定电流 : 32mA~1

Rated Current: 32 mA~1

额定电压;125V/250V/400V AC

Rated  Voltage:125V/250V/400 AC

1-3标示Marking

保险管上需要有下列标示

The fuse shall have the following marking:

规格:特性符号+额定电流+额定电压

Specification:Characteristic  Symbol+Rated Voltage

32mA~800mA : _mA    1A~1:_A

Trade mark:The Manufacture’s Logo+Part Number+Approvals

32mA~1: TUV UL CSA CQC

注意:对标示字样大小没有规定

Note:Size of the markings have not be specified.

2.适用范围

SCOPE

适用于一般电子设备。Used in electronic equipment.

3.工程图和结构

OUTLINE DRAWING AND STRUCTURE

3-1 工程图(?挝唬?m)

Outline Drawing and Dimensions(Unit:mm)

3-2结构Structure

编号

No.

元件

Component

材质

Material

数量

Quantity

(1)

熔丝

Wire

合金

Alloy

1

(2)

铜帽

Cap

黄铜镀镍

Brass with mickel plated

2

(3)

本体

Body

陶瓷管/胶料

Ceramic Tube/Plastic

1

(4)

引线

Lead

镀锡铜线

Tinned Copper wire

2


4.外观及形状

APPEARANCES AND CONFIGURATION

4-1外观:外观不应有显著的污点、铁锈或者裂纹

Appearances:There shall not be any remaekable stain,rust or crack on the appearances.

4-2形状:轴向引脚的超小型保险丝

Configuration:Axial Leaded Micro-Fuse.

5.物理特性

PHYSICAL CHARACTERISTIC

5-1 拉力测试

Tensile test

沿端子的轴向施加10N的拉力,持续1分?,管体不断开、破裂。

Keep pulling the cap of the fuse with 10N at axial direction for 1 min,and the pipe body is continuously opened and broken.

5-2管体强度测试

Strength of fuse tube

保险管管体固定好后,在管体中央部位施加15N压力,管体不断开、破裂。

After the fuse pipe body is fixed, the 15N pressure is applied to the center position of the pipe body, and the pipe body is continuously opened and broken.

6.?气特性

ELECTRICAL CHARACTERISTICS

% of Ampere Rating

Ampere Rating

Opening Time

100%

32mA - 1

4 Hours, Min.

200%

32mA - 1

60 Second, Max

275%

500mA~ 10A

300 msecs., Max.

400%

500mA~ 10A

30 msecs., Max.

1000%

500mA~ 10A

4 msecs., Max.

规格判定Item

系统AVL1

2nd souece(AVL2)

TAPYE

Slo-Blo

无资料

Openrating Temp

-55℃~125℃

-55℃~125℃

Temp.derating Currev

无资料

无资料

大熔断时限

200% Rating 60SEC

60sec MAX(小于60)

突波实验

3millisecond at 1000% rated current

3millisecond at 1000% rated current

Melting I 2 t

3.14

3.14

Cold Ohms

1A/0.13~0.15 Ohm

1A/0.13~0.15 Ohm

Interrupting rating

50A/125VAC

50A/250VAC

50A/250VAC

50A/400VAC

Dimensions

7.2mm*¢2.6mm

7.2mm*¢2.6mm

Ssfty

UL CSA

CCC

7.环境特性

ENVIRONMENTAL SPECIFICATION

7-1 操作温度范围:-55℃~125℃

Operating Temperature: -55℃~125℃

7-2 保存条件

Storage Conditions

温度:+10℃~60℃

Temperature: +10℃~60℃


在相对湿度≤75%下平均可存放3年

On average, It can be stored below the relative humidity or 75% for 3 years.

在非露天下,相对湿度为95%下多可存放30天。

Without dew, It can be kept under humidity of 95% for 30 days.

8.焊接条件

SOLDERING PAAMETERS

8-1波峰焊

Wave Solder

焊接温度:260±5℃

Soldering Temperature:260±5℃

焊接时间:4 Sec. Max.

Soldering Time:4 Sec.Max.

8-2手工焊锡

Manual Solder

焊接温度:350±5℃

Soldering Temperature: 350±5℃

焊接时间:3 Sec. Max.

Soldering Time: 3 Sec. Max.

9.其他使用注意事项

OTHER NOTICE IN USING

如果需在保险管上加热缩套管,烘烤温度与时间需要参照以下规定

If heat shrink tubing was needed,the roast temperature and time should be refer to the following.

设定烘烤温度:不大于150℃  烘烤时间:50s Max.

The temperature should be sel under 150℃,roast time:50s Max.



伟德BV下载 | 伟德BV下载 | 产品展示 | 技术支持 | 在线留言 | 联系我们 |
伟德BV下载  2020 版权所有

Copyright 2020 Auto Parts All Right Reserved

粤ICP备:10219780号-2

点击这里给我发消息